PremiumLine Frost-protected eye shower, with Underfloor Activation (Stainless Steel), for floor mounting
The frost-protected, self-draining eye showers with underfloor activation are designed to be frost-proof. The underfloor activation mechanism is installed in a frost-protected area approximately 1 meter below the floor surface and ensures that the eye shower drains when deactivated. The Eye shower is activated via the foot lever; deactivation is performed using the additional black handle on the shower’s standpipe.
Or call us directly at: +49 40 538 092 70
(Mo – Thu from 8 a.m. to 5 p.m. and Fri from 8 a.m. to 14 p.m.)
- EN 15154-2:2025
- ANSI Z358.1-2014
Technical specifications
| Material | Stainless steel |
|---|---|
| Surface | polished |
| Height (mm) | 1040 |
| Width (mm) | 350 |
| Length/Depth (mm) | 380 |
| Operating pressure (bar) | 2,5 – 5,0 |
| Volume flow (l/min) | 14 ±10% tolerance |
| Water connection | 3/4″ male |
| Water outlet / drain | 1 1/4″ male |
| Mounting type | Floor mounting |
More about this product
Product description
The eye shower is equipped with two B-SAFETY high-performance spray heads that not only meet the requirements of EN 15154-2:2025 and ANSI Z358.1-2014, but also ensure wide-area water distribution. This ensures that the areas around the eyes are also covered, and positioning the eyes within the water stream is straightforward. The controlled, even, and—above all—gentle water stream is optimized for flushing chemicals out of the eye.
The integrated flow regulator ensures the correct spray height and a spray pattern that complies with standards, regardless of the water pressure. The rubber sleeves around the spray head protect the person seeking assistance from impact injuries. Dust caps on the spray head protect against dirt and open automatically due to water pressure when the Eye shower is activated. The large holes in the spray heads prevent standing water and thus scale buildup.
Technical Description
- Operated via a T-shaped stainless steel foot pedal with black anti-slip tape, 350 mm wide, secured to the angle pulley system with a stainless steel cable
- Stainless steel angle bracket for the pull rod, with a stainless steel mounting bracket on the upright
- Stainless steel ball valve for in-floor activation, installed in a stainless steel enclosure, with a 1000 mm pull-rod actuator, 3/4″ male water inlet, DIN-DVGW tested and approved, with automatic drainage at a depth of 1000 mm
- Stainless steel base with 4 mounting holes, polished, dimensions 200 x 200 mm
- 1 1/4-inch stainless steel riser, polished, with a 1 1/4″ female water inlet at the bottom, height above floor 1040 mm
- Stainless steel connection pipe for easy installation and alignment of the shower, polished
- Integrated automatic flow regulator: 14 liters per minute, +/-10% tolerance, for a standard-compliant spray pattern at a specified operating pressure range of 2.5 to 5 bar
- High-performance, wide-spray stainless steel spray heads, polished, with a plastic spray plate, largely free of calcification, including a rubber protective cover and a tight-sealing Dust cap with a folding mechanism, mounted via a Distributor fork
- Stainless steel drip pan, 275 mm in diameter, polished, 1 1/4″ male drain connection
- sign for eye shower according to EN ISO 7010 und ASR A1.3, self-adhesive PVC-film, 100 x 100 mm, viewing distance 10 metre
- Height above floor: 1,040 mm, projection: 380 mm, width: 350 mm
- in accordance with BGI/GUV-I 850-0, DIN 1988, and EN 1717
- in accordance with ANSI Z358.1-2014 and EN 15154-2:2025
accessories
